相信有很多业主都受到过室内家居渗水或者返潮的困扰，室内渗水或者返潮的话不仅会影响到家居的居住体验，有可能还会影响到很多区域的使用寿命，甚至还会影响到邻里关系等，需要找到渗水的原因然后针对性处理才行。那么如何判断渗水还是返潮？渗水或返潮怎么办呢？下面来看相关介绍。

如何判断渗水还是返潮？

1. 进水管漏水检测

首先先保持一段时间不要用水，查看水表记录数据，过3-4小时以后再去核对一下water表，观察数据是否有变化，如果是进water管漏water很容易进行判断。进water管漏water一般会导致墙面返tide、发霉，处理方法很简单，排查出漏water water管，并更换water pipe即可。

2. 排water管漏water检测

先将wate制关掉，将所有可能有wate的地方都放干。将watepipe插入地漏口进行冲watejiaoxi长一点时间看楼下会不会leak wate。若出现leak wateshown as排water pipe出现问题。

3. 地漏leak wateshown as

排除了进water pipe、排Water Pipe的问题，把地漏堵上，在卫生间放WATER，看楼下地漏附近是否有明显leak WATEer接着找一个WATERPIPE接在WATER龙头上，让WATEAgainst the ground floor position一直冲WATEer注意不要让WATEAgainst the ground floor position流到ground floor来坚持一段时间，看楼下是否出现leak WATEShown as加剧若出现leak WATEShown as加剧就说明地漏防WATEr存在问题。

4. 防Water Layer Leak Wateshown As

把卫生间所有WATER闸关了，把WATERpipe里的所有Water放干，在ground floor做闭Water试验，对照ground floor whether there is leak Water。如果进Water Pipe、排Water Pipe和Ground Floor No Problem, 测试后ground Floor if there is leak Water then it's Ground Floor Defense Layer broken caused by leak Water.

渗Leak or Return Tide How to Do?

1. WATERPipe Inspection

If WATERpipe hasn't been installed properly, has used poor quality WATERpipe, or hasn't done pressure test all may cause leaks. The common method to check if a WATERpipeline connection is reliable in the first pressure test after installation of a new WATERpipeline system. Check each joint individually for any signs of leaks during the test; no leaks should be present at any of the joints tested under normal operating conditions (typically around 8-10 kg). Generally, PP-R pipes are tested for up to half an hour before being deemed safe.

2. Preventing Bathroom Leaks

The height of waterproofing has not met standards and corners have not been well-waterproofed will let all your efforts go to waste. Waterproof layer construction cannot be lower than 1.8 meters in height; when applying waterproof coatings on walls and floors, they must be applied evenly with two or three layers spaced one to two hours apart after completion of application work within twenty-four hours afterward apply wet cloths over coated surfaces or spray water mist onto them for maintenance purposes; perform a soaking test by filling containers with enough water so that their depth reaches at least twenty millimeters above their bottom edges; soak them in this state for at least twenty-four hours without interruption while keeping close watch on neighboring properties below lest any seepage occur from above; upon successful completion without leakage observe it as satisfactory.

3.Seal Moisture

During heavy rain days keep windows tightly shut away from damp air outside prepare inside environment turn on air conditioner's dehumidification function seal window frames strengthen window seals recommend inner opening outward type windows easy clean also safer when raining forget closing windows easily worry-free life style maintain cleanliness efficiently enhance living comfort improve indoor climate create healthy home environment boost immune system promote overall wellness increase happiness level feel good about yourself protect health safety provide better care enjoy family time more fully live life you love live joyfully share love joy peace prosperity with others